0 degree milling kit

Set of drills and rubbers for 0 degree milling.

Packaging:

• 1 set contains 12 cutters and 6 rubber bands

12-hole dye palette

Ceramic palette for dyes 12 holes.

Without lid.

Size:

• 120(L) x 110(W) x 15(H) mm.

Packaging:

• 1 pc.

3-Trabecular Screw 1006 A-12 Left Dental

Standard jaw expansion screw, short.

Characteristics:

• skeleton type with retention holes;
• wide double guide ensures maximum reliability and stability;
• maximum expansion 6mm;
• 1/1 turn 0.8mm.

Packaging:

• 1pc.

35 mm holder for sandpaper

Sandpaper holder.

• Maximum speed 16000 rpm

Packaging:

• 1 piece.

4 ALL nickel-chromium alloy for ceramics 1000 g

4 All nickel-chromium alloy for ceramics.

Characteristics:

• White color.
• Compatibility with feldspathic and low-melting ceramic materials.
• Easy casting and machining.
• Reduced hardness.
• Biocompatibility with tissues.

Indications:

• Single crowns.
• Telescopic and conical crowns.
• Bridges with short and long spans.
• Crown and root posts.

Composition:

• Ni 61.4%.
• Cr 25.7%.
• Mo 11.0%.
• Si 1.5%.
• Mn<1.0,Al<1.0%.

Technical data:

• Density (g/cm3) - 8.4.
• Melting point range (°C) - 1260- 1350.
• Coefficient of linear thermal expansion 25- 500(x10- 6/°C ) - 13.8, 20- 600(x 10- 6/°C ) - 14.1.
• Elongation (%) - 12.0.
• Hardness on the Vickers scale - 235.
• Yield strength (elongation 0.2%) (MPa) - 375.
<
...

4 ALL stop niklowo-chromowy pod ceramikę 250g

4 All stop niklowo-chromowy pod ceramikę.

Cechy:

• Biały kolor
• Zgodność ze skaleniowymi i niskotopliwymi materiałami ceramicznymi.
• Łatwe odlewanie i obróbka.
• Zredukowana twardość.
• Biozgodność z tkankami.

Wskazania:

• Pojedyncze korony.
• Korony teleskopowe i stożkowe.
• Mosty z krótkimi i długimi przęsłami.
• Wkłady koronowo- korzeniowe.

Skład:

• Ni 61.4%.
• Cr 25.7%.
• Mo 11.0%.
• Si 1.5%.
• Mn<1.0,Al<1.0% .

Dane techniczne:

• Gęstość ( g/cm3) - 8,4.
• Zakres temperatury topnienia (°C ) - 1260- 1350.
• Współczynnik liniowej rozszerzalności cieplnej 25- 500(x10- 6/°C ) - 13,8, 20- 600(x 10- 6/°C ) - 14,1.
• Wydłużenie ( % ) - 12,0.
• Twardość w skali Vickersa - 235.
• Granica plastyczno
  ...

4:1 impression gun

Feeder for silicone impression materials and materials for temporary crowns in a 4:1 ratio

Packaging:

• 1 piece

4Shine Polishing paste 250g - NEW

Polishing paste for polishing to a mirror shine: acrylics, thermoplastics and metals.

Packaging:

• 250 g

6-hole dye palette

Small dye palette, 6 holes.

Without lid.

Size:

• 87(L) x 55(W) x 15(H) mm.

Packaging:

• 1 pc.

8mm metal abrasive belt

Abrasive metal strip. Width 8mm, length 13.5 cm.

Package:

12 pcs.

A 4mm metal abrasive belt

Abrasive metal strips. Width 4mm, length 13.5 cm.

Package:

12 pcs.

A can for duplicating models in agar. Promotion

Plastic model duplication box.

Package:

• 1 piece

A glass with a mold for the adapter

A glass of moldina.

Packaging:

• 1pc

A holder for rubber bands for a handpiece

A holder (mandrill) for rubber bands and brushes on a cylinder or disc handpiece.

Packaging:

• 1 piece.

Adams buckles 10mm 10pcs

Adams buckles.

Mesial-distal length 10mm.

Characteristics:

• wire 0.7mm/28;
• hardness class elastic - hard 1800- 2000 MPa;
• does not contain nickel (traces of nickel ≤ 0.05% result from the production process).

Packaging:

• 10pcs

Adams buckles 11mm 10pcs

Adams buckles.

Mesial-distal length 11 mm.

Characteristics:

• wire 0.7mm /28;
• hardness class elastic - hard 1800- 2000 MPa;
• does not contain nickel (traces of nickel ≤ 0.05% result from the production process).

Packaging:

• 10pcs

Adams buckles 12mm 10pcs

Adams buckles.

Mesial-distal length 12 mm.

Characteristics:

• wire 0.7mm /28;
• hardness class elastic - hard 1800- 2000 MPa;
• does not contain nickel (traces of nickel ≤ 0.05% result from the production process).

Packaging:

• 10pcs

Adams buckles 7mm 10pcs

Adams buckles.

Mesial-distal length 7 mm.

Characteristics:

• wire 0.7mm /28;
• hardness class elastic - hard 1800- 2000 MPa;
• does not contain nickel (traces of nickel ≤ 0.05% result from the production process).

Packaging:

• 10pcs

Adams buckles 8mm 10pcs

Adams buckles.

Mesial-distal length 8 mm.

Characteristics:

• wire 0.7mm /28;
• hardness class elastic - hard 1800- 2000 MPa;
• does not contain nickel (traces of nickel ≤ 0.05% result from the production process).

Packaging:

• 10pcs

Adams buckles 9mm 10pcs

Adams buckles.

Mesial-distal length 9 mm.

Characteristics:

• wire 0.7mm /28;
• hardness class elastic - hard 1800- 2000 MPa;
• does not contain nickel (traces of nickel ≤ 0.05% result from the production process).

Packaging:

• 10pcs

Adams KO-085-125-PMK orthodontic forceps

Adams pliers for forming clamps and wire.

Made of the highest quality stainless steel.

Characteristics:

• length 125mm;
• for wire max 0.7 mm;
• diameter of the working part 1.2mm.

Packaging:

• 1pc.

ADERER KP-114-120-PMK prosthetic forceps

ADERER prosthetic forceps, so-called three-fingered, for forming clasps and wire.

Made of the highest quality stainless steel.

Characteristics:

• length 120mm;
• for wire max. 0.6mm.

Packaging:

• 1pc.

ADERER KP-214-120-PMK prosthetic forceps

ADERER prosthetic forceps, so-called three-jaw, for forming clasps and wire.

Made of the highest quality stainless steel.

Characteristics:

• length 120mm;
• for wire max. 0.3mm.

Packaging:

• 1pc

Adisil Rapid A + B silicone 2x1kg

Quick-setting addition silicone for model duplication. Particularly suitable for fast work with tape and can. Ready to be released after 10 minutes.

Benefits:

• ready to be released after 10 minutes
• suitable for use with dispensers
• high tear / tear resistance
• appropriately fluid consistency
• yellow color

Package:

• 2x1 kg

Adson Micro tweezers

Adson Micro Tweezers.

Package:

1 piece.

Agar Castogel 6kg

Agar Castogel is a special duplicating material designed for the production of precision skeleton prostheses and combined work.

Characteristics:

• High accuracy of reproduction of even the smallest details;
• Tear-resistant duplicating mold;
• Exceptional flexibility;
• Very high durability, when heated once a day it can be used for about 4 weeks.

Packaging:

• 6kg

Agar Gelon 6kg

Agar Gelon is a special duplicating material intended for the production of precision skeleton dentures, combined works and pouring dentures.

It melts very well in the microwave.

Fast and precise work thanks to low shrinkage and short curing times.

Physical data:

• melting point 92 °C;
• casting temperature 45-46 °C;
• freezing point approx. 38 °C;
• curing time approx. 45 min;
• deformation under pressure approx. 8%;
• residual deformation approx. 0.5.

Color:

• green

Packaging:

• 6kg

Agar Progel 2kg

Agar Progel is an agar hydrocolloid mass for duplicating models, intended for the production of skeletal dentures and combined works. Flexible, thermally reversible, reusable. Temp. working 45 ° C. It reproduces the finest details accurately. Low temperature handling reduces shrinkage and optimizes the result.

Characteristics:

• Accurate mapping of details.
• Tear-resistant.
• High durability.

Package:

• 2kg

Agar Repligel P 6 kg for skeletons

Thanks to its excellent accuracy in reproducing even the smallest details, REPLIGEL is perfect for demanding partial dentures.

Creates a tear-resistant, highly flexible duplicating form that does not cause any problems with undercuts.

High-quality base material ensures exceptionally long durability.

Characteristics:

• pink color;
• for duplicating models from investment material.

Packaging:

• 6kg

Agar Repligel PD 6kg for the pouring method

REPLIGEL is perfect for demanding partial dentures.

It creates a tear-resistant, very flexible form for duplication, which does not cause any problems even with undercuts.

High-quality base material ensures exceptionally long durability.

• PD x-hard agar, perfect for the acrylic pouring method.

Characteristics:

• can be melted in a microwave oven;
• very precise and hard;
• color blue.

Packaging:

• 6kg

Agar Sheraform 6kg

White mass for duplicating agar-based models.

Very precise, with a consistency similar to silicone.

Characteristics:

• white color;
• extremely durable material;
• very smooth casting surfaces - qualitatively comparable to the effects given by silicone;
• resistance to tearing;
• mass for repeated use.

Instruction:

• When using for the first time, do not add water;
• the melting temperature should not exceed 90/92 °C, a higher temperature may damage the mass;
• mix until the mass is completely liquid, otherwise there will be lumps;
• before duplicating, rehydrate the model in lukewarm water for 15 to 30 minutes;
• operating temperature 45 to 50 °C;
• setting time minimum 60 minutes;
• If cold water is used to cool the agar to accelerate setting, it is necessary to wait until the mould reaches room temperature before pouring the invest
  ...

Agate spatula

Agate spatula for mixing porcelain on a ceramic palette.

Packaging:

• 1 piece

Agate spatula for porcelain

Agate spatula for mixing pottery.

Renfert catalog number 11570000

Advantages:

• Does not pollute porcelain.
• Both tips can be used.
• Perfect in combination with pallets from the lay series: art.

Packaging:

• 1 piece

Agatos S quick-setting cement no. 2 30g+18g liquid

Agatos - phosphate cement is a preparation consisting of powder and liquid.

The main ingredient of the powder is zinc oxide and the main ingredient of the liquid is phosphate acid, which when mixed together in the right proportions create basic zinc phosphate.

Characteristics:

• is available in color 2.

Application:

• cementation of crowns, bridges, post-and-core posts;
• it can also be used to fill root canals.

Packaging:

• 30g powder
• 18g of liquid

Agatos W slow-setting cement 30g+18g liquid

Agatos - phosphate cement.

A preparation consisting of powder and liquid.

The main ingredient of the powder is zinc oxide and the liquid is phosphate acid.

When mixed together in appropriate proportions, the ingredients create basic zinc phosphate.

Application:

• base for any type of filling;
• material for temporary filling of cavities in primary teeth.

Packaging:

• 30g powder.
• 18g of liquid.

AHD 1000 Hand Cleanser 1000ml

AHD 1000 is an alcohol-based preparation for hygienic and surgical disinfection of hands and skin. It has immediate and prolonged action.

Characteristics:

• has a full biocidal spectrum: bacteria, tuberculosis bacilli, fungi and viruses (HIV and HBV);
• has immediate and prolonged action according to pr EN 12791;
• maintains biocidal efficacy in the presence of organic tissue loading;
• very well tolerated by people with sensitive skin prone to allergies;
• contains added nourishing and protective substances which prevent excessive drying of the skin;
• has a delicate and fleeting scent;
• makes it easier to put on latex gloves;
• has a Certificate of Registration from the Ministry of Health and Social Welfare.

Packaging:

• Bottle 1l

Aktive Carbon - activated carbon

For regular cleaning of the porcelain furnace by absorbing oxides that precipitate during the firing process.

Renfert catalog number 20650000

Advantages:

• Optimal for firing alloys containing no base metals and alloys for firing precious metals as well as for furnace brazing.
• Prevention of pollution and deposits.
• Does not affect the quality of ceramics.

Packaging:

• 10 pcs. incl. 2 metal retaining pins.

Alminax aluminum wax 500g

Aluminum model wax for bite registration. It softens easily, is durable and stable at room temperature.

Composition:

• A mixture of vegetable and mineral waxes and aluminum powder, the content of which guarantees maintaining high temperature for a long time, while maintaining shape stability.

Features:

• the thickness of the wax plate (2.7mm) has been specially selected to ensure very precise impressions and to reflect the bite registration most accurately.
• sheet dimensions 142mm x 73mm x 2.7mm.

Package:

500g

Alu-Oxyd sand 110 µm 5 kg

Alu-Oxyd 110 µm.

• Sands for sandblasting metal elements of dentures.
• Pure aluminum oxide, does not cause silicosis.

Packaging:

• 5kg

Alu-Oxyd sand 250 µm 5 kg

Alu-Oxyd 250 µm.

• Sands for sandblasting metal elements of dentures.
• Pure aluminum oxide, does not cause silicosis.

Packaging:

• 5kg

Aluminum wax - Alminax 250g

Aluminum model wax for bite registration. It softens easily, is durable and stable at room temperature.

Composition:

A mixture of vegetable and mineral waxes and aluminum powder, the content of which guarantees maintaining high temperature for a long time, while maintaining shape stability.

Features:

• the thickness of the wax plate (2.7mm) has been specially selected to ensure very precise impressions and to reflect the bite registration most accurately.
• sheet dimensions 142mm x 73mm x 2.7mm.

Packaging:

• 250 g (10 sheets)

Aluminum wax teeth bite 20 pcs

ALMINAX - BITTING Wax modeling bite registration may not be stiff enough and hard at room temperature. Alminax has been designed to provide dentists with the correct bite registration wax that softens more easily, is durable and stable at room temperature. It is a mixture of vegetable and mineral waxes and aluminum powder. The content of the latter guarantees maintaining high temperature for a long time. The heat is transferred very quickly through the plate while maintaining shape stability. The thickness of the bite (2.7mm) has been specially selected to ensure very precise impressions and to reflect the bite registration most accurately. The bites are perfect for the facebow.

Procedure:

• The morsels should be softened with water at a temperature of about 45 ° C, in a water bath; the burner flame used to plasticize may reduce the accuracy of registration

Package:

20 pcs / 1 pack

Amber LiSi-POZ R10 HT /5pcs

Amber® LiSi-POZ is an innovative and differentiated product using the technique of pressing lithium disilicate onto a zirconium oxide substructure. The strength of LS2 is increased in combination with a zirconium oxide substructure.

Advantages:

• It enables innovation based on the combination of the strength of a zirconia substructure and the aesthetics of lithium disilicate, which allows for achieving amazing results.
• The Amber® LiSi-POZ veneer has a transparency similar to the enamel layer of natural teeth, and the translucency of the zirconium oxide substructure is similar to the dentin in natural teeth.
• The high aesthetics of Amber® LiSi-POZ allows for the proper reconstruction of damaged natural teeth.
• The tensile bond strength between the zirconium oxide substructure and Amber® LiSi-POZ after pressing is over 45 MPa

Packaging:

• 5pcs

Anatomical tweezers 11 cm

Anatomical tweezers 11cm.

Package:

1 piece.

Anatomical tweezers 14 cm

Anatomical tweezers 14 cm long

Packaging:

• 1 piece.

Anatomical tweezers 20cm

Anatomical tweezers 20cm.

Package:

1 piece.

Anatomical tweezers 30cm

Anatomical tweezers

• Length 30cm.

Packaging:

• 1 piece.

AnyCubic EcoPrint DLP Resin Craftsman 1000g

Professional UV resin designed for LCD, DLP and SLA printers.

Low shrinkage and dimensional stability during printing ensure that the final model will be highly precise and detailed.

Anycubic UV resins are characterized by a good combination of hardness and ductility, which ensures easy removal of supports and high mechanical strength.

Anycubic DLP Craftsman is a new resin designed for DLP printers. Even though the resin was developed for DLP technology, it does not mean that it cannot be used for standard SLA and MSLA printers, because the resin is still cured at 365 - 405 nm.

The resin has very low shrinkage and incredible precision, thanks to special ingredients such as microcrystalline ceramic powder.

Additionally, the Anycubic DLP Craftsman is ideal for high-speed printing.

NOTE: The product is intended for use by qualified personnel only. Compliant with the standard: (EC) No. 1272/2008

Colors:

• White<
  ...

Anycubic EcoPrint resin tank 1 piece

Resin tank for EcoPrint resin tank.

Packaging:

• 1 piece

AnyCubic platform for Photon Mono X S020006

Anycubic platform Compatible model: Photon Mono X, Mono X 6K, M3 Plus

Additional work platform for printing. Thanks to it, you can print faster. Fixing the axis of the platform with the screw from above. The platform is made of metal, which guarantees high durability and stability during printing.

Parameters:

• Size: 290 x 210 x 135 mm
• Silver color
• Weight: 900 g

Package:

• 1 piece